The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.Tamborriel,TamborrielSubmersible slurry pump,　　Fire fighting awareness is deeply rooted in the hearts of the people. With the improvement of fire fighting awareness,TamborrielSplit vertical pipeline pump, many people pay more and more attention to fire pumps. Some places also began to pay attention to the selection of fire pumps. In many places, fire control cabinets are also installed under the full set of fire control systems. In earlier years, fire control　　The two have certain commonalities. They are both submersible. As the name suggests the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumpingAnnaba,　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.

　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　Consider the vertical separation level of the tail equipment. The water pump control cabinet has a variety of protection s and complete status display, such as overload, short circuit, phase loss protection, motor over temperature and electric leakage, as well as single pump and multi pump control working modes a variety of main and standby pump switching modes and various　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.Quality improvement,　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.

　　Under the action of auxiliary devices, it can transport the slurry, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal useRecommendation and consultation,　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.　　Check the oil quality of the oil chamber every six months to see if there is any leakage,TamborrielCirculating hot water pipeline pump, and force replacement; Check the impeller for wear and determine whether it needs to be repaired and replaced.　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.Tamborriel,　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, and the current will slowly increase during use. Well, we should choose　　 The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.