Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Turkwan,Just like the failure of the walking part of the lifting platform, the operator must master the common sense of equipment maintenance and failure, so that he will not appear too flustered when a failure occurs. Generally speaking the common faults of the walking parts of the lifting platform are divided into: bearing pad burning,TurkwanIndustrial cargo elevators, axle box bearing burning, traction motor bearing burning, wheel tire relaxation collapse and other fault problems. Below, I will share with you the solution.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion,The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.

Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line,TurkwanProfessional production of cargo elevators, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, which is simple and easy to operate. The models are divided into fixed and mobile forks, and there are many options for ordinary legs and straddle legs. It is very suitable for warehouse, supermarket retail merchandise placement, and extraction.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.Supply chain quality management,What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, table size mm *mm, the price is about - yuan; the rated load is - tons, the price is about yuan. Rated load the table size is mm*mm lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!

Correct construction elevator site inspection First of all,TurkwanGuide rail lifting cargo elevator, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Professional is king,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.The operating rod is heavy. The operating rod mechanism is faulty. Check, adjust, and replace unqualified parts; clean the valve parts; check the hydraulic oil cleanliness and the valve core is stuck (manufacturing, installation problems, dirt problems)Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent,The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.