At the same time, the Ministry of construction attaches great importance to the application of stainless steel pipes. The industry standard of stainless steel water pipe was issued and implemented in . The Ministry of construction has issued documents on relevant technical specifications and installation sets of pipeline engineering, which are being prepared by Tongji University. All kinds of stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe are qualified. Welcome to telephone inquiry and sincerely invite cooperation! At present, there are stainless steel pipes in Sichuan, Guangdong, Zhejiang, Jiangsu and other places, and the products have become mature. Therefore, the time for application has come.Hardness stainless steel pipes are usually measured by Brinell, Rockwell and Vickers hardness indexes.Brcko,Cold rolled steel strip shall be delivered in the state of heat treatment (annealing, normalizing and tempering after normalizing), and shall be delivered smoothly.Argon shall conform to the rules of national specifications, and argon with purity of % shall be selected. If the content of impurities is too high, the maintenance effect of argon will be weakened and the weld quality will be indirectly affected.Lismore,AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti, CrNiTi, ocrnimoti, etc. Duplex stainless steel has good weldability, and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content, it is easy to form & sigma; Pay attention when using.The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.Model & mdash; Commonly used precipitation hardening stainless steel model, usually also called -; %Cr,%Ni.

Measures to improve the welding quality of stainless steel pipe in order to ensure that the outer surface of stainless steel pipe is not damaged and purified, the maintenance of stainless steel pipe should be strengthened in each process of consumption, mainly including the following three aspects: the processing and consumption of stainless steel pipe should have a special consumption workshop (wood board is well used) , avoid the machining platform of austenitic stainless steel and carbon steel or solid overhead.Steel etching belt, stainless steel stretching belt, stainless steel soft belt, stainless steel hard belt, stainless steel medium hard belt stainless steel high temperature resistant belt, etc.The experimental ice load of concrete decorated stainless steel pipe is the highest in the cold areaoriginal,Measures to improve the welding quality of stainless steel pipe in order to ensure that the outer surface of stainless steel pipe is not damaged and purified, the maintenance of stainless steel pipe should be strengthened in each process of consumption, mainly including the following three aspects: the processing and consumption of stainless steel pipe should have a special consumption workshop (wood board is well used) , avoid the machining platform of austenitic stainless steel and carbon steel or solid overhead.Duplex stainless steel product description: This stainless steel has good corrosion resistance in urea carbamate solution and high stress corrosion cracking resistance in chloride environment. At the same time, the duplex stainless steel has excellent mechanical properties and can be used in plant construction with high safety requirements.Stainless steel pipe, which was consumed and used at the end of the s, and relevant parties are starting from reducing wall thickness and money, so as to facilitate further implementation. In order to promote stainless steel pipe, since the s, China has started to reduce wall thickness and cost; High diameter to wall ratio and high precision & rdquo; The technical effect of stainless steel pipe makes the stainless steel pipe lose its application and expand quickly. There are various connection modes of stainless steel pipes. The rare types of pipe fittings include contraction type,BrckoHow much is the stainless steel pipe, compression type, union type, push type push thread type, union flange connection socket welding type welding type and derivative series connection mode combining welding with traditional connection. These connection methods have different application ranges according to their principles, but most of them are convenient, firm and reliable. The sealing ring or gasket materials used for connection are mostly silicone rubber, nitrile rubber and EPDM that meet the requirements of national specifications, which eliminates the worries of users. In the construction of water supply pipe system, due to the glorious history of galvanized steel pipe, all kinds of new plastic pipes and composite pipes have been lost and developed rapidly, but they are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. In direct drinking water, hotels and public places at the international level have been equipped or are equipped with direct drinking water pipelines. In many cases, stainless steel pipe has more advantages, especially the stainless steel pipe with wall thickness of only . ~ mm has the characteristics of safety, reliability, sanitation, environmental protection economy and applicability in high-quality drinking water system, hot water system and water supply system that puts safety and sanitation first. It has been proved by engineering theories at home and abroad that it is not only one of the new, energy-saving and environmental protection pipes with good comprehensive function of water supply, but also a very competitive water supply pipe, which will play an unparalleled role in improving water quality and improving people's living standard.

Various welding methods of combined welding stainless steel welded pipe have their own advantages and disadvantages. Combined welding methods include argon arc welding plus plasma welding, high-frequency welding plus plasma weldinghow,According to the purpose, it can be divided into oil well pipe (casing, pipeline pipe, boiler pipe, mechanical structure pipe, hydraulic prop pipe, gas cylinder pipe, geological pipe, chemical pipe (high-pressure chemical fertilizer pipe, petroleum cracking pipe) and marine pipe.　　· Sewage treatment system.The back side is not protected by argon, and the flux coated welding wire (self protective flux cored welding wire) + TIG process is adopted. In the s, the backing welding wire has been developed. Recently, China has also developed the stainless steel backing welding wire (i.e. flux coated welding wire, such as tgftgftgftgf,BrckoUltra thin 304 stainless steel strip,BrckoPrice of stainless steel pipe, etc.) It has been applied to the actual construction and achieved good results. We have successfully applied it in the capacity expansion and reconstruction project of Urumqi Petrochemical.Brcko,Good ductility, used for forming products. It can also be machined to harden rapidly. Good weldability. Wear resistance and fatigue strength are better than stainless steel.Accounting for about % - % of the total steel, it is widely used in the national economy. Because the steel pipe has a hollow section, it is suitable for gas and solid transmission pipelines; at the same time, compared with the round steel of the same weight, the steel pipe has large section coefficient and high flexural and torsional strength, stainless steel pipe itself is an economic section steel that saves metal. It is an important part of steel the structure and components formed by pipe have a larger section modulus than solid parts. Therefore, especially in oil drilling, production and metallurgyThere shall be a special storage rack. The storage rack shall be a wooden or painted carbon steel support or padded with rubber pad to isolate it from carbon steel and other metal materials. During storage, the storage position shall be convenient for lifting and absolutely isolated from other data storage areas. Protective measures shall be taken to avoid purification, collision with other components, purification and damage of iron metal.