The back side is not protected by argon, and the flux coated welding wire (self protective flux cored welding wire) + TIG process is adopted. In the s, China has also developed the stainless steel backing welding wire (i.e. flux coated welding wire such as tgftgftgftgf, etc.) It has been applied to the actual construction and achieved good results. We have successfully applied it in the capacity expansion and reconstruction project of Urumqi Petrochemical.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.Rimouski,Usage: widely used in automobile, tractor and other industries. Series & mdash; Martensitic precipitation hardening stainless steel.Turmero,Deburring: after the pipe is cut off, the burr shall be removed to avoid cutting the sealing ring.Martensitic stainless steels typical martensitic stainless steels include Cr ~ Cr and Cr, which have good processing properties. Deep drawing, bending, but preheating is required before welding. crlcr is mainly used to make corrosion-resistant structural parts such as steam turbine blades, low-temperature equipment components in refrigeration industry, and can be used as stainless steel spring and clock spring after deformation strengthening.

Model & mdash; Add a small amount of sulfur and phosphorus to make it easier to cut.The product ground by the grinding belt.Production process of stainless steel welded pipe: raw material - strip - welded pipe - end repair - polishing - Inspection (spray printing) - Packaging - shipment (warehousing) (decorative welded pipe).How much is it,Austenitic stainless steel. It contains more than % chromium, about % nickel and a small amount of molybdenum, titanium, nitrogen and other elements. Good comprehensive performance and resistance to corrosion of various media.There is a bright future for domestic substitution for imported stainless steel pipes. Since the s, China has solved the problem of reducing wall thickness and cost; High diameter to wall ratio and high precision & rdquo; The technical problems of stainless steel pipe make the stainless steel pipe applied and developed rapidly. If a pipeline can be fully applied, localization is indispensable. At present, some domestic have the ability to produce and further develop stainless steel pipes and fittings.Model & mdash; The addition of sulfur improves the processability of the material.

Stainless steel pipe packing bag is nothing more than the function of protecting the surface of stainless steel pipe, so most stainless steel pipe users do not have to question this point.details,Martensitic stainless steels typical martensitic stainless steels include Cr ~ Cr and Cr,RimouskiStainless steel tape, which have good processing properties. Deep drawing, bending, crimping and welding can be carried out without preheating. Crl does not require preheating before cold deformation, but preheating is required before welding. crlcr is mainly used to make corrosion-resistant structural parts such as steam turbine blades, while crcr is mainly used to make surgical and wear-resistant parts of medical instruments; crl can be used as corrosion-resistant bearings and tools.The steady creep rate is usually used to evaluate the long-time creep performance of materials. For the application of long-life materials, the steady-state creep rate of stainless steel pipe under high temperature and stress is the key index of the material, and can be extrapolated. The following are the test results of stainless steel pipe under different test conditions. The results show that the steady-state creep rate of stainless steel pipe sample is in the order of magnitude after creep at ℃ (mpa ℃ (mpa) for h; when the temperature condition increases to ℃ (the stress decreases to MPa), the creep performance of stainless steel pipe sample is good, and the steady-state creep rate is in the order of magnitude; when the temperature further increases to ℃ (the temperature creep rate of mpa stainless steel pipe sample increased to ℃ (mpa steady-state creep rate reaches the maximum value under several test conditions, and creep fracture occurs. See for the change of steady-state creep rate of stainless steel pipe sample under several conditions. When the temperature increases, the material maintains a low level of creep rate. Under ℃ MPa, s creep deformation rate does not increase,RimouskiStainless steel bright annealed tube, which shows little influence on the temperature and stress,Rimouski314 stainless steel strip, and creep fracture occurs under this condition Compared with several other common structural materials, it can be seen that the creep performance of several materials is better than that of ordinary materials under all test conditions. After hours of test, the total strain does not exceed .%. The curve is relatively stable and the fluctuation is small, indicating that the test data is stable and reliable. Stainless steel pipes are widely used because of their excellent corrosion resistance It is widely used in petrochemical industry, pipeline transportation and other working conditions with strong corrosive media. The main reason for the corrosion resistance of stainless steel pipes is the addition of a large number of elements CrNi, and Cr is the main element determining the corrosion resistance of stainless steel pipes. The electrode potential of stainless steel pipes jumps with the increase of Cr content. However, stainless steel pipes are in the subsequent heat treatment During the treatment Cr element will precipitate into the matrix in the form of carbide. On the one hand, the hardness of Cr carbide is larger than that of the matrix and the service wear process can improve the wear resistance of stainless steel pipe. On the other hand, the precipitation of Cr containing carbide will lead to Cr Element dilution zone in some parts of the matrix, increase the number of batteries of the material, reduce the electrode potential of stainless steel pipe and reverse the corrosion Therefore, in order to obtain good corrosion and wear resistance, the combination of mechanical properties and corrosion resistance of stainless steel pipe materials needs to be considered. At present, some scholars have studied the effects of austenitizing temperature and time, it is found that austenitizing temperature can change mechanical properties, but has little effect on corrosion performance, while tempering temperature has a great effect on the corrosion resistance of materials. Appropriate austenitizing temperature and tempering temperature can improve the corrosion and wear resistance of materials. Some scholars use surface treatment to improve the corrosion and wear resistance of materials, It is concluded that low-temperature nitriding forms a diffusion layer on the surface of the material, improves the wear resistance of the material, interacts with Cr and chemically stable phase -fen to improve the corrosion resistance of the material.Standard classification - classification: national standard GB industry standard Yb local standard enterprise standard qcb- classification: product standard packaging standard basic standard - standard level (divided into three levels): y level: international advanced level I level: international general level H level: domestic advanced level - national standard: stainless steel bar (level I) gb- stainless welding disc Park (level H)Rimouski, Series & mdash; martensitic precipitation hardening stainless steel pipe. & mdash; high strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment and the hardness can reach hrc. It is one of the hard stainless steels. A common application example is & ldquo; shaving blade & rdquo;. There are three common models: C and f (easy processing type).The recrystallization temperature changes with the shape variable. When the shape variable is %, the recrystallization temperature drops to ℃, and the recrystallization annealing temperature of cold deformed austenitic stainless steel is ~ ℃. At ℃, it needs to be kept warm for h, fully burned at ℃, and then water-cooled.