Fourth, model selection parameters: outlet diameter, flow, dust,MadrugaWear resistant slurry pump, motor power, pumping rate, maximum particle and weight.　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipmentMadruga,　　 When the electric pump is not in use, take it out of the water and do not immerse it in the water for a long time, so as to reduce the chance of the motor stator winding getting damp and increase the service life of the electric pump. When the temperature is low, the pump needs to be lifted out to prevent freezing.　　 the water pipe shall be short and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.Netrakona,　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed

　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　In order to facilitate the disassembly of the impeller, during the design of the slurry pump, the impeller is connected with the pump shaft through reverse buckle. This is why the impeller will be turned off when installing a new slurry pump. Therefore, we must pay attention to the impeller marked on the pump body during preliminary installation and use　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.agent,　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　Rate.　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible

　　Superior complete protection s, reasonable structure,MadrugaIrrigation deep well pump, the water pump will automatically start to supplement the pipe network pressure.For more, please check,　　Promote the continuous expansion of the sales network group.　　 Low vibration and noise, low motor temperature rise,MadrugaTwo stage slurry pump, no pollution to the environment.　　At the same time the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.Madruga,　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.