Fault phenomenon: fan motor overload, fan deformation; Fan motor fault; Fan motor thermal relay fault (aging); Loose wiring; Cooler blocked; Large exhaust resistance. Cold storage fault phenomenon: dryer does not operate, compressor line is disconnected fuse is blown, high voltage switch acts thermal relay acts, compressor is locked, line is falsely connected or loose fault phenomenon: it stops in a short time after drying,GuadalupeHow much does it cost to install a small cold storage, ambient temperature is too high condenser is blockedDuring production in the production workshop, the unit weight of Pu warehouse board shall not be less than the unit weight required by the project, not less than & plusmn; kg/m.Guadalupe,The transportation tools used in the controlled atmosphere storage shall meet the requirements of relevant standards.Judge the operating sound of the compressor, and carefully listen to the operating sound of water pump, cooling tower, compressor, fan and other equipment. In case of abnormal sound, timely warranty is required, so as to avoid greater damage to the compressor due to untimely warranty.Filiasi,GuadalupeTemperature monitoring of medical cold storage,When outdoor air enters the cold storage body, it will not only increase the cold consumption of the cold storage, but also bring water into the warehouse. The condensation of water will lead to the building structure, especially the heat insulation structure, being damaged by moisture and freezing. Therefore, a moisture-proof and heat insulation layer should be set to keep the cold storage board building moisture-proof and air-proof performance and good sealing.When installing the polyurethane insulation board, the adhesion between the panel of the polyurethane insulation board and the thermal insulation material is short and often high.Polyurethane foam foam dimensional stability: cold storage polyurethane foam in severe temperature changes or at a relatively low temperature will appear dimensional changes (as contraction), the size changes often reflect bubble cracking or falling off, and these will inevitably affect the normal use of cold storage. In addition to regular simulation of performance testing, more emphasis is placed on the selection of high quality materials: special energy polyether compound use, so that the foam body mesh structure, greatly improving the foam low temperature resistance. At present, polyether commonly used in spraying materials contains a large number of functional components, and a large number of linear structures formed after reaction are difficult to be stable at low temperature; The use of the energy crosslinking agent also greatly improved the dimensional stability of the foam. The selected polyether adopts catalysis in the production stage, and the reaction is complete, so that the polyether maintains a high reaction rate (that is, it can react completely with black material); Some manufacturers in order to achieve foam appearance does not produce deformation phenomenon and add a hole component to foam material, reduce the bubble closed hole rate, achieve the effect of stable size, but it has sacrificed the thermal insulation performance of polyurethane cold storage insulation material foam.

Danfoss thermal valve is adopted for the thermal valve of the cold storage, with guaranteed quality; Due to the high temperature requirements of the cold storage and the high degree of automation and regulation of the temperature, the temperature system of the cold storage adopts microcomputer full-automatic, does not need special people to operate, and can be remotely controlled. When the temperature exceeds the specified range, it will automatically alarm which is of great significance to the proper preservation of the cold storage.Expensive, high machining precision of body parts; High noise during compressor operation; Screw compressor can only be used in medium and low pressure range, not in high-pressure occasions; Due to large fuel injection and complex oil treatment system, there are many auxiliary equipment of the unit.The closed cell structure and surface material of polyurethane rigid foam with good moisture-proof, waterproof and corrosion resistance make it have better air resistance and water vapor resistance, and it can be made into inlaid connection structure during forming, which is easy to assemble. It does not need additional insulating layer to prevent moisture and saves a lot of trouble in laying insulating layer.Welcome calls ,The type of cold storage to be built in the type of cold storage should be determined according to the type of circulating goods. For example, the cold storage that only circulates vegetables can only build a fresh-keeping cold storage, while the cold storage with refrigeration + freezing will be built if there are many types of circulating goods and great difference in storage temperature. As for the size of the cold storage, it should be determined according to the type, quantity, cycle, whether to use shelf stacking and so on. For example, for fruits and vegetables packed in cartons, the storage capacity of -kg per cubic meter can be referred to, and the size of cold storage construction can be estimated in combination with the storage capacity rate of about .-.. - floor installation of cold storage: first level the floor, then install the floor, select a beautiful floor and put it in a conspicuous place, and do a good job in the floor and evaporator drainage system.Cold storage construction: which one is suitable for you? Which one is suitable for you?

It will still decrease. The humidification amount will decrease by % at degrees.Excellent quality, and corresponding protection measures shall be taken for the installed equipment.The electrical contacts shall compress the wire connector and the main wire connector of the motor, which shall be clamped with a wire clamp, and tin shall be hung if necessary.The service life of the cold storage depends on the quality of the refrigeration equipment, but it also has a great relationship with the proper daily management and maintenance after the installation of the cold storage. Many times, people often ignore the latter point. In daily life, as long as we maintain and maintain the cold storage regularly, we can greatly improve the service life of the cold storage and reduce the cost.Guadalupe, professional cold storage installation, installation of cold storage, cold storage construction, fruit preservation cold storage, medical cold storage,GuadalupeWhere is it cold, large quantity, excellent quality and low price, fire resistance - Waterproof - high temperature resistance, strong and durable, carefully observe the oil return of the compressor and keep it clean. If it is found that the oil level is not clean enough or the oil level drops, replace it with new oil in time so as to avoid bad compressor and reduce the service life of the compressor.How to maintain the refrigeration compressor in the cold storage in order to prolong its service life and reduce the occurrence of faults in the use process. The refrigeration compressor in the cold storage needs regular maintenance. Here we introduce the maintenance of the compressor in the cold storage.