Soak in water Veneer method: stick the wood veneer on the board surface.For example, the high price solid wood veneer is pasted on the low price solid wood floor. Although this is also the solid wood floor, it deceives consumers.Houston, it is recommended to use pure solid wood floor. Sticker method: stick the same wood grain paper on the front and back of the board.An Nuhud,thicknessThe first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.The flame retardant grade is B, including pur Crystal Shield transparent layer, wear-resistant layer, color film layer, SPC polymer rural base and soft sound insulation rebound layer.Its foreign home decoration sales market is very hot, especially suitable for home furniture floor.Melamine surface coating is generally used for wallboard, tabletop board, etc. it is used in places with low wear resistance requirements. In the flooring industry, this kind of surface coated floor is called 'false floor'Its wear-resistant revolution is only - revolutions. If it is used with high strength, the decorative paper on the surface will wear out after two or three months. The standard laminate floor will not have such a problem after years of normal use. There is no wear-resistant layer on this kind of floor decorative paper,HoustonHow much is the wooden floor per square meter, the pattern is beautiful and clear, and it is relatively smooth when touched by hand, which is the place where laymen are easy to be fooled.Total quality management,From to Chinese traditional pure solid wood flooring and new solid wood flooring,HoustonAsh wood floor, which means three-layer and double-layer solid wood, have been surging in an undercurrent.In recent years, new solid wood has maintained a high annual growth rate of more than %.Under the economic development layout from to , the upgrading of solid wood flooring category caused by new solid wood will become an important driving force to promote the consumption boom of home decorative flooring.The world financial storm has an impact on China&#;s wood flooring industry chain, but it is not rampant, only lack of confidence in the market.The operation track of the development of market economy has been advancing in the cycle system of wave soldering and wave trough. The flooring industry is depressed and it is not easy to hold it for a long time. China has a strong foreign demand market, and the demand of China&#;s home building materials market is still very large. Look at the section of the board. Skin allergy.

SPC floor surface will not have holes and water seepage;There will be no seams after splicing. After being stained, wipe it gently with a rag to clean it easily, leaving no marks that are difficult to remove,HoustonOutdoor waterproof wood floor, and there is no need to maintain it with special maintenance products.Sales DepartmentPrecautions for solid wood floor installation : prevent the assembly from being too loose or too tight. Carefully grind with water gauze until the surface is a little rough, remove the powder and apply a second layer of paint.Precautions for solid wood floor installation : solid wood floor cannot be used immediately after disassembly and packaging.Houston,The biggest highlight is that they are not afraid of water and shop willfully anywhere.Some people say that this method is unscientific and laminate floors can&#;t soak in water, but I have done some experiments and come to another conclusion Overweight articles shall be placed stably. Furniture and heavy objects shall not be pushed, pulled or dragged hard to avoid scratching the surface of the wear-resistant layer.