X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater,San AndraHow much is 114 seamless pipe per ton, gas, heating steam and other general liquids X-ray or ultrasonic testing sampling inspection (%) shall be carried out. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.San Andra,Due to the impact of poor visual . Only through the application of mesh and the overall stiffness can we see the potential of demand. The application of steel data is a high one, such as the reuse rate of mesh and reinforcement installed in the current mesh production company and the treatment of corrosion. The design strength value of circular reinforcement and the design strength value of welded reinforcement mesh. According to the equal strength substitution principle and considering comprehensive factors, the use of steel welded mesh plate can save the use of steel bars in the steel welded mesh plate factory. And the reinforcement mesh needs to be processed after it is shipped to the site, so there is no wear.The finished product has smooth surface, low friction coefficient,San AndraT-welded pipe manufacturer, flatness error + / - mm / m length, wear resistance and maximum temperature of ℃Bo, I-beam has no specific composition and performance series.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.

Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.It is also divided into general welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, idler pipe, deep well pump pipe, automobile pipe, electric welding thin-wall pipe, electric welding special-shaped pipe, scaffold pipe and spiral welded pipe.What is the stainless steel passivation of alloy pipe?Price,→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, weldability and structural size of I-beam.

Key technical characteristics of alloy pipeHigh quality and low price,When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.There are several ways to clean galvanized pipesDifference and application description between H-beam and I-beamSan Andra,The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Introduction to product knowledge of alloy pipe:As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.