it will also lead to the burning of the motor.　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore, in fact, it is mainlyCiudad Juárez ,　　The long shaft deep well pump is equipped with two types of motors: ordinary vertical Y series motor (equipped with PTS thrust disc) and hollow shaft YLB series motor for deep well pump. The insulation grade is divided into class B and class F. now, with the progress of science and technology and the continuous development of products, YLB series has developed high-voltage, protection and other grades up to　　Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active powerSanta-Ana,Ciudad Juárez Irrigation deep well pump,　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample,Ciudad Juárez WQ submersible sewage pump, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　Fourth, model selection parameters: outlet diameter, flow, dust,Ciudad Juárez Vertical non clogging sewage pump, motor power, impeller speed, pumping rate, maximum particle and weight.

　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　 requirements for suction filter pipe　　In fact the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corrodedQuality assurance,　　 Then reinstall the equipment on the engine and install the rubber hose.　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact, the motor temperature will rise, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　The actual operating flow is too large, resulting in the following results: when the flow increases, the shaft power of the pump increases, while the efficiency of the motor remains unchanged, so the power of the input motor must increase. Excessive power makes the motor in an overloaded operation state, which may cause heating or even burn out the motor　　The other mechanical seal is a split seal,　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local places　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.