Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal,Johannes Linstead Corrosive pipeline pump, mechanical seal, etc.Johannes Linstead ,　　 It is not allowed to operate the electric pump at high lift for a long time, and try to control it within the range of the proposed use lift, so as to prevent the electric pump from burning out the motor due to overload.　　However there is also a disadvantage of using the auxiliary impeller sealing system,Johannes Linstead Used pipeline pump, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coalAdjadabia,Johannes Linstead ZD slurry pump,　　No matter what type of slurry pump you need Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　For example in the market, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.

　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.　　 The electric pump should not be used in flammable and explosive environment, nor should it pump flammable liquid. How to use the submersible non clogging sewage pump?　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.Safety and health,　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.

　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one　　The treatment methods are as follows: Check the power supply voltage: if the voltage changes greatly, it is caused by unstable voltage, and the use should be stopped immediately to prevent more serious consequences. Or install corresponding heat dissipation protection measures to protect the motor.　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.Johannes Linstead ,　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, so it is easy to burn out the motor.　　Water flow into the bearing damages the bearing.　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent