Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.Martinique Island, do not disassemble and repair it without authorization, but carry out professional maintenance immediately.　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board,Martinique IslandVertical centrifugal slurry pump, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pumpAndhuei,　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　Basically, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people

　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary,Martinique IslandCentrifugal slurry pump, at a certain temperature,　　Balance of.　　The utility and durability of the utility model, so the polymer composite materials are generally used in production.　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.

　　At the same time the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.Affordable price,　　When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view, it is to convert electrical or chemical energy into gravity　　Fire fighting awareness is deeply rooted in the hearts of the people. With the improvement of fire fighting awareness many people pay more and more attention to fire pumps. Some places also began to pay attention to the selection of fire pumps. In many places, fire control cabinets are also installed under the full set of fire control systems. In earlier years, fire control　　However, there is also a disadvantage of using the auxiliary impeller sealing system,Martinique IslandSubmersible non clogging sewage pump, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coalMartinique Island,　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron, and infiltrate tin evenly.　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular