The development of submersible slurry pump is to adapt to increasingly complex working conditions, that is and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, in the traditional slurry pump　　 We must choose to consider the actual use situation when making the selection,Corpus ChristiVortex pump and pipeline pump, because there will be some difference between the marked head when using and the head when using. This is because the pipe itselfCorpus Christi,　　(b) The maximum ambient air temperature varies with seasons, but does not exceed ℃.　　Water flow into the bearing damages the bearing.Kruje,　　However, there is also a disadvantage of using the auxiliary impeller sealing system,Corpus ChristiSubmersible slurry pump, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.

　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　In order to improve the service life of the submersible sewage pump, most domestic and foreign manufacturers are now trying to find a way on the pump protection system that is, in case of leakage,Corpus ChristiRubber lining submerged slurry pump, overload, over temperature and other faults of the pump, it can give an automatic alarm and automatically shut down for maintenance. However, we believe that in the submersible sewage pump　　The pump should be divided into two aspects: electricity and machinery. As for machinery, you can compare the previous maintenance records. The second is electricity. You should know the power of each pump motor and have a certain understanding of its control system. Slurry pump with mechanical sealWhere can I find it?,　　We also need to limit the starting frequency and select appropriate thermal protection devices for use.　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), and dry it naturally.　　 Next it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when

　　 First, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeveSampling inspection,　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　 Gradually disassemble the outlet pipe, gate valve and elbow with installation tools, and tighten the next section of water pipe with pipe clamping plate. In this way, it cannot be lifted by force, and the customer service points shall be moved up and down, left and right for safe lifting and removal)　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.Corpus Christi,　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　What is the order.