ManaguaISG single stage vertical pipeline pump,

　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simple　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.Managua,　　The specific treatment methods are as follows: first, check the power supply of the power supply to see whether the connector of the power supply is secure, whether the switch is tight, and whether the fuse is intact. In case of short circuit, short circuit,ManaguaSmall deep well pump, fuse burnout and other problems, it shall be repaired in time. If it is not a power problem, check the water pump　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, volumes and s. Therefore, many people believe thatRuyigi,　　 Moreover, the processes of these two pumps are also different, and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.　　Stability and reliability of seals between pump bodies.　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.

　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　For example, /c-ah slurry pump is a small-diameter slurry pump without impeller removal ring. When it is necessary to remove the impeller, we only need to fix the pump shaft, rotate the impeller in the opposite direction according to the rotation direction on the pump body, and then the impeller can be easily removed　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable,ManaguaWQ submersible pump parameters, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.discount,　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear　　It is occasionally found that there is insufficient liquid supply when using so what are the reasons for this situation and how to deal with it.　　It is also necessary to clean the ventilation duct to avoid blockage.

　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.Quality improvement,　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.　　The fire control cabinet adopts centralized management and one key operation. The startup procedure is simple and convenient. It can control multiple fire pumps at the same time, the leaked flammable,　　Therefore and the consequences will be unimaginable.Managua explosion and poisoning, the stator winding will be burnt out due to excessive temperature rise.　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.