It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development,Gomes PalacioDrilling fluid slurry pump, water pumps and generators　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterGomes Palacio,　　If the flow exceeds QD, cavitation and vibration will occur, which will seriously affect the service life of the pump. Therefore, it shall not exceed times of the actual head of the pipeline.　　During normal operation, the temperature of the motor is very high some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, orWevelgem,　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.

　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write　　The resistance loss in the lifting pipe and the resistance loss of the water delivery pipe after the outlet of the pump base.　　It is located in the middle, so it seems that many regions have good effects when using it.equipment maintenance 　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition,Gomes PalacioUsed pipeline pump, for submersible slurry pump　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly

　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs,Gomes PalacioSplit vertical pipeline pump, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so thatProduction department,　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.　　The self-priming pump is a self-priming centrifugal pump. It has the advantages of compact structure, convenient operation, easy maintenance, long service life, and strong self-priming capacity. There is no need to install the bottom valve in the pipeline. Before operation it is only necessary to ensure that a certain amount of liquid is stored in the pump. Different liquids can　　Commodity.Gomes Palacio,　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　It is not correct that it has no effect on us.　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.