Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close,Boya HotelHorizontal non clogging sewage pump, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.Boya Hotel,　　The main shaft of the water pump is bent or the main shaft of the water pump and the motor is not concentric or parallel.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft soIpswich,　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.

　　At present,Boya HotelCirculating hot water pipeline pump, mechanical seals occupy an increasing share in the slurry pump seal market.　　That is, first, check whether the equipment operation noise is reasonable; second, check whether the alarm unit has leakage and overheating alarm signals; third, check whether the vibration of the guide rod is normal; fourth, the cause shall be yzed and reported in time.　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.Convenient and efficient,Boya HotelISG single stage vertical pipeline pump,　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.

　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used so it will be blocked after being used for a period of time　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurryreform,　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.　　 Pressure control: external electric contact pressure gauge or pressure controller can automatically turn on and off the pump according to the change of pipe network pressure. This type is widely used in domestic water supply and fire pressurization systems.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.Boya Hotel,　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.