When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.Villa bisono,　　 With protection . cf fire control cabinet integrates many electrical components, which can form a three-dimensional protection for the fire pump, including voltage overvoltage and undervoltage protection, current overcurrent and undercurrent protection, overload protection, phase loss protection, overheating protection, etc. this　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller,　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved　　 During the installation of smooth bearing components,Villa bisonoSingle stage slurry pump, if the installation is correct, the smooth oil is appropriate, the repair is timely,Villa bisonoCarbon steel explosion-proof pipeline pump, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write

　　 If the hot water within ℃ is recommended the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　Unsuitable pump head is selected.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.Discount,　　The premise of using this method is that the water gun must have sufficient flow during use otherwise the effect of the submersible slurry pump may not be obvious.　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.

　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,Customer first　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　 Check the suction pipe and bottom valve to see if there is any air leakage source. Remove the silt and other obstructions at the water inlet. Check the water inlet depth of the bottom valve to ensure that it is not less than times the diameter of the water inlet pipe. If it is not enough, deepen the water inlet depth of the bottom valve.　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterVilla bisono,　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　The of descending axial force can be used for slurry transportation in power plants hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min,Villa bisonoSmall deep well pump, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.