Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustmentPort au Prince,Port au PrinceRubber lining submerged slurry pump,　　 Service conditions　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in useChristian San, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, ore slurry %; It can be operated in series according to the needs of users.　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity and can effectively pass through large solid particles. It is not limited by suction range, and the investment is lower.　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment,Port au PrinceAh slurry pump, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.

　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be　　Many customers need to replace the impeller after purchasing the slurry pump. What if the impeller of the slurry pump cannot be disassembled?　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.Process inspection　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use,Port au PrinceFire deep well pump, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　 Moreover, the processes of these two pumps are also different and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.

　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.Statistics,　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so　　During normal operation, the impeller of the slurry pump becomes tighter and tighter as it turns. The more it is used, the easier it will operate. However, if the slurry pump reverses, it will directly cause the impeller of the slurry pump to fall off. The slurry pump must be disassembled and then re inspected, installed and tested.　　With the continuous development of slurry pump technology, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.Port au Prince,　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will　　Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.