Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.lubbock ,　　Operation, maintenance and upkeep During the operation of the electric pump, always observe the current, voltmeter and water flow and strive to make the electric pump operate under the rated working condition.　　Submersible slurry pumps are mainly used in mining, metallurgy, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump bladeNovi Pazar,　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to　　It is not correct that it has no effect on us.

　　In this way, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less, and the fact is　　Or nodular cast iron, vertically split, bolted. The pump body is connected with the bracket with bolts. The discharge outlet of the pump can be rotated and installed at intervals of ℃ and eight angles as required.　　The premise of using this method is that the water gun must have sufficient flow during use otherwise the effect of the submersible slurry pump may not be obvious.Inspection items,　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other,lubbock Sewage pump diving,lubbock Vertical multistage centrifugal pipeline pump, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　 in addition,lubbock Carbon steel explosion-proof pipeline pump, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!

　　If the pump outputs more medium liquid, it will certainly do more work. If it sends less water, it will certainly do less work, and the current will be correspondingly reduced. Pump power (kw) = head (m) × Flow (m/s) × The gravity of the fluid (kg/m for water) divided by (power conversion factor) divided by the efficiency of the pump (aboutquery,　　It is not correct that it has no effect on us.　　 Drain the water filled in the motor.　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the waterlubbock ,　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.