Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products, etc.Corallillo,Square tube flattening test is a kind of test to check the deformation performance of metal tubes (seamless square tubes and rectangular tubes) flattened to the specified size and show their defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards. Requirements for samples samples can be taken from metal pipes with qualified appearance. Generally, sawing is adopted. The inner and outer walls of the pipe shall retain the original surface without any processing. Sample length L & asymp; D (D is the outer diameter of the pipe). When the outer diameter is large, the length l shall not exceed mm. When the outer diameter is less than mm, l = mm. When cutting the sample, the surface of the sample shall not be damaged and the performance of the metal shall not be changed due to heating or cold processing. The edge of the section shall be flattened. The flattening test is a test to check the deformation performance of the metal pipe (seamless square pipe and rectangular pipe) flattened to the specified size and show its defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards.When sand blasting or manual mechanical derusting is used,CorallilloQ235A square tube, due to the falling off of the oxide scale of the galvanized square pipe, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, affecting the adhesion of the paint film. I am engaged in all kinds of square tubes, seamless square tubes, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material, the overstock of inventory is easy to expire. Therefore, and the paint can be used only when the results meet the standards.Union-de-Reyes,Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~ which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes,Corallillo120654 galvanized square tube, on-site settlement, honest operation, local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon, manganese, sulfur, phosphorus etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)

Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.Production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, British standard square tube, American standard square tube,CorallilloLatest quotation of galvanized square pipe, European standard square tube and non-standard square tube.Welding seamless welding seamless is to make welded elbows. After grinding and pickling, sand blasting, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.Quality recommendation,Change to square pipe: generally, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes square rectangular tubes, galvanized square tubes seamless square tubes, galvanized tubes, on-site settlement, honest operation, local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.

Stage ( & mdash; )target, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionCorallillo,Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.With the progress of the times and the faster and faster economic development, the places where large-diameter seamless square tubes are used are becoming more and more popularAfter chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, resulting in electrode potential difference, so the steel surface treatment requirements are very high.