The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.Kirche,Any work carried out at a height of meters or above should be considered as work at height. Any work that can be done in advance on the ground must be done on the ground to minimize high-altitude operations.The hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil,KircheElectric hydraulic lifting platform, the overflow valve is stuck or severely worn, the spring of the overflow valve is fatigued and deformed resulting in unstable pressure regulation of the overflow valve, and the relief time of the overflow valve is too short, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn, it should be replaced.Kelaniya,KircheMast type aluminum alloy hydraulic lifting platform,Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.The undercut length of the weld mm should not exceed % of the weld seam, and the depth should not exceed .mm.

This paper briefly introduces some matters needing attention in the selection of oil tank for hydraulic elevators. The main functions of the hydraulic oil tank for elevators in the hydraulic system of elevators and hydraulic elevators and other hydraulic machinery are oil storage, heat dissipation, separation of air contained in oil and elimination of foam.Oil cylinder leaks. Long term use causes wear on the sealing ring in the oil cylinder and excessive oil leakage in the cylinder wall gap resulting in the natural descent of the hydraulic cargo elevator. The sealing components need to be replaced immediately.What are the methods for reducing shaking on lifting platforms? Reducing the shaking of the lifting platform can reduce the psychological obstacles of the operators, ensure the smooth progress of the operation, and also greatly help improve safety. Warm reminder: safety, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, we will analyze the working principles of elevators. The types of elevators are generally divided into the following: fixed elevators, This type of elevator uses hydraulic oil cylinders and pump stations to transmit power, the length of the support rod for the scissor fork, the number of layers, the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, stable lifting, and high safety.Meticulous workmanship,Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch, it should be suitable for the operating power.Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.

Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.How many?,Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.Today,KircheSelf propelled hydraulic lifting platform, we will share with you why hydraulic cargo elevators are ideal equipment for transporting goods?Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.Kirche,Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.Reason: The lowering speed valve is out of adjustment. Cleaning method: If the lowering speed valve is adjusted, and if the adjustment is ineffective, replace it with a new valve.The undercut length of the weld mm should not exceed % of the weld seam, and the depth should not exceed .mm.