the whole industrial and mining system operates stably

　　Third, and the operation of the pump will not affect the work of the whole industrial and mining system.　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.Moncrova,　　As a display screen, the operation of each fire pump is clear at a glance, and the management is very convenient.　　Many users, including new practitioners of slurry pumps,MoncrovaBooster pipeline pump, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?Frydek-Mistek,　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　Some impurities will entangle the impeller, so generally, the open impeller will be used, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating

　　A large amount of lubricating oil is stored.　　Test the steering first, and then connect the motor to the ash pump. There is a removal ring at the journal. This device can prevent the impeller from reversing.　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,Good quality　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section the fixing nut on the shaft shall be　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.

　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pumpCredit guarantee,　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　In order to maintain the original treated water volume without increasing the number of water pumps,MoncrovaDrilling fluid slurry pump, the liquid level in the storage tank can be increased by adjusting the floating ball in the liquid tank. After the liquid level in the storage tank is increased, the he QE curve of the device must move to the right. At this time, the head at the intersection of the two curves becomes smaller and the flow remains　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!Moncrova,　　At present,MoncrovaHH slurry pump, mechanical seals occupy an increasing share in the slurry pump seal market.　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　The whole packing body, including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane