Advantages of using I-beam: reduce maintenance cost, reduce downtime, reduce wear, reduce equipment capacity and increase power consumptionAfter determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Kuchowe,Galvanized; hot-rolling;Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace, chemical industry, electric power, boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.Bel Air,Application characteristics of I-beamWhen it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, the chemical raw material transmission pipeline has a wide indoor space.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal,KuchoweReinforcement engineering turnover, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.

d. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information and the performance parameters in the production process are monitored by the central control room.Galvanized pipe has excellent corrosion resistance. Compared with traditional steel, its application life is longer. Secondly, this kind of pipe has strong resistance to baking. In case of critical situation, it will not lead to the collapse of building structure in a short time. In addition, this kind of pipe also has a practical advantage, that is, it is more convenient and lighter when carrying out the construction and installation. The operators save time and labor when carrying out the construction, and the operation efficiency has been greatly strengthened. In this regard it is not difficult to understand why the galvanized pipe is so favored by various construction units.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Welcome calls ,→ the two surfaces of the flange are parallel to each other making it easy to connect,KuchoweHow much is I-beam per meter, process and install.Requirements of alloy tubes for low and medium pressure boilers Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.

Classification introductionassets,When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Galvanized pipe is often seen in our daily life, especially in some construction sites. This product has the advantage of durability when used. It also has the characteristics of surface gloss, uniform zinc layer and no missing plating. Moreover, the cost of hot-dip galvanizing for rust prevention is lower than that of other paint coatings. In addition, this product also has the characteristics of no dripping, strong adhesion, breaking the clean Legion and strong corrosion resistance. Even if it is used in some places where the environment is not good its service life is also very long, in urban or offshore areas, standard urban or offshore areas can be maintained for years without repair. The products produced by our company must meet these requirements. Friends who need to order can call us directly.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Kuchowe,I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Maanshan Iron and steel, Xuanhua Iron and steel, Japan iron and steel, etc.According to the theory of steel structure, that is, the I-beam should be standing rather than lying down.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.