Be sure to choose a pump that is more suitable for use.　　Other ysts believe that, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especiallyPosarika,　　During installation, check whether the installation position conforms to Chinese standards, which reduces the vacuum degree of the pipeline pump and affects the suction lift. Water inlet pipe　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerBoksburg,　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost,PosarikaQJ submersible pump, long-term operation cost and operation reliability.

　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　It is worth noting that the QW mobile type is generally used without a fixed position, so it is usually used temporarily without an electric control cabinet, and a special person is required to control the shutdown of the water pump.　　Work, no noise and vibration, and the site is cleaner.Recommendation and consultation,　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　If the oil seal ring of the shaft is seriously worn replace it with a new one.　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.

　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakagetarget,　　So it is called: submersible slurry pump.　　 No maintenance: if it is not used continuously after startup, the submersible pump will rust and cannot be started. If it is not used for a long time, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.Posarika　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use,PosarikaZD slurry pump, multiple pumps need to be used in parallel or standby pumps need to be prepared.　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults