During the use of the goods yard medical cold storage project, the stored goods must be in strict accordance with the relevant regulations. The goods should have a certain distance from the ground and wall of the cold storage. When stacking, the distance between the goods and the goods must be cm. At the same time,St. CatherineInstallation and design of cold storage, the distance between the goods and the cold fan should also be cm. No goods can be stored within this range, This is also an important content in the use of medical cold storage engineering.The insulation board of the cold storage adopts polyurethane double-sided color steel plate. The main effect of this cold storage insulation board is good sealing performance, insulation effect and moisture-proof effect, so as to ensure the refrigeration effect of the cold storage. The electric cold storage door is adopted for the cold storage door,St. CatherineRefrigerated vegetable cold storage, and the cold storage management personnel can timely and effectively open and close the door when entering and leaving, so as to avoid the loss of refrigeration capacity of the cold storage.St. Catherine,Frozen and refrigerated storage begins to shift to shelf and pallet storage in accordance with & amp; amp; ldquo； FIFO & amp; amp; rdquo； This is conducive to improving the quality of commodity storage and reducing losses.Moreover, polyurethane does not produce harmful gas at high temperature.Japan,Thermal insulation rigid polyurethane has low thermal conductivity and good thermal performance. When the density of rigid polyurethane is ~ kg / m, the thermal conductivity is only . ~ .w / (m.k), which is the lowest among all thermal insulation materials at present.The evaporator surface is too thick or too much dust, and the heat transfer effect decreases: another important reason is that the heat transfer efficiency of evaporator is low which is mainly caused by excessive frost or excessive dust on the evaporator surface.The construction of cold storage in site selection bears the circulation of low-temperature goods. Therefore, the transportation convenience of cold storage construction site should be given priority in site selection, such as proximity to roads, railways, etc. At the same time, the location of the cold storage should avoid large pollution sources and direct sunlight, and the construction of the cold storage should have good drainage and ventilation conditions.

The cold storage board uses light polyurethane as the inner material of the cold storage board. The advantage of polyurethane is that the thermal insulation performance is very good. The exterior of polyurethane cold storage board is composed of SII, so as to make the cold storage more energy-saving and improve the working efficiency of cold storage.Which one is better,No matter whether the food cold storage or quick-frozen storage is in use, it is inevitable that there will be various small faults. Don't be nervous when there are problems. You can find or eliminate problems according to the knowledge taught today.Tips for fresh-keeping storehouse wholesale: the specific functional characteristics of the seafood machine in the fresh-keeping storehouse wholesale are simple to operate, and the microcomputer system is adopted, and the temperature can be adjusted at will; The seafood machine unit has compact structure and stable performance. Users only need to connect the power supply and the cooling water pipeline to put it into operation; The wholesale seafood machine condenser in the fresh-keeping warehouse adopts internally threaded copper pipe. Good heat exchange effect; The seafood machine adopts pure titanium tube evaporator, which has good cooling effect and strong performance; The seafood machine unit wholesale in the fresh-keeping warehouse has extraordinary pressure sealing test and the performance of each component is particularly good; The seafood machine unit has the advantages of low noise, low vibration, fast cooling, long service life, multiple quality protection devices, high cost performance and good quality. The seafood machine can be customized according to customer requirements; Many fruit wholesalers will transform the original warehouse into a fruit preservation warehouse in order to store fruits for a longer time. Due to the huge difference between warehouses, it needs a lot of attention to transform the warehouse into a qualified energy-saving fruit preservation warehouse.Whether the parameters of refrigeration equipment are consistent. When the cold storage leaves the factory, set the parameters on the refrigerator. During use, the air humidity is high and the defrosting interval is long. The common cold storage boards of cold storage include mm, mm, mm, mm and mm polyurethane thermal insulation boards, color steel tiles, stainless steel plates, salt thick steel plates, embossed aluminum plates, polyurethane spraying,St. CatherineInstallation and maintenance of maintenance cold storage, etc. on both sides or single and double sides, more general color steel tiles are produced and processed into hidden grooves, which have light weight, high compressive strength, good fire resistance, corrosion resistance and aging resistance, The cold storage board is simple and convenient to assemble, and is a wide range of raw materials selected for the heat insulation and heat preservation of the cold storage. The cost of stainless steel plate and salt plate increases, and it is also easy to deform and damage the appearance.St. Catherine, and the professional cold warehouse shall be installed. The cold warehouse shall be installed. The cold warehouse shall be constructed. The fruit fresh-keeping cold warehouse and medical cold warehouse shall have high pressure rating, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection and long service life. The corner shall be temporarily fixed with . color plate angle steel; When installing each wall panel, evenly apply two layers of foaming material on the joint surface of male and female groove, and apply one layer of foaming material when installing polystyrene wall panel. The blanking shall be uniform and continuous; After the wallboard is installed in place, pull rivets at the lap joint of the internal and external steel plates of the two wallboards for connection and fixation, and the rivet spacing in the warehouse should be mm; When connecting the library plate in the form of eccentric hook connection, the eccentric hook shall be loosened once before installation to ensure reliable locking during installation.At ordinary times, users should check the sealing degree of the gap of the cold storage, the heat transfer effect will be reduced: once more refrigerant oil is attached to the inner surface of the evaporator heat transfer tube, the heat transfer coefficient will be reduced. Similarly, if there is more air in the heat transfer tube, the heat exchange area of the evaporator will be reduced, the heat transfer efficiency will be significantly reduced and the decline rate of warehouse temperature will be slowed down.